قم بتنزيل 三菱 PLC デバイスモニタ : And2PLC على جهاز الكمبيوتر باستخدام GameLoop Emulator

三菱 PLC デバイスモニタ : And2PLC على الكمبيوتر الشخصي

三菱 PLC デバイスモニタ : And2PLC ، القادم من المطور chosyoshinsya ، يعمل على نظام Android في الماضي.

الآن ، يمكنك لعب 三菱 PLC デバイスモニタ : And2PLC على جهاز الكمبيوتر باستخدام GameLoop بسلاسة.

قم بتنزيله في مكتبة GameLoop أو في نتائج البحث. لا مزيد من الانتباه إلى البطارية أو المكالمات المحبطة في الوقت الخطأ بعد الآن.

ما عليك سوى الاستمتاع بجهاز 三菱 PLC デバイスモニタ : And2PLC على الشاشة الكبيرة مجانًا！

三菱 PLC デバイスモニタ : And2PLC مقدمة

It is an application that can perform I/O device monitor and device writing of PLC (Mitsubishi sequencer) via Wi-Fi. If the Wi-Fi router is connected to the PLC's EtherNet module, the Android smartphone can be connected to the PLC via the router. The EtherNet module can be connected if it has a built-in Ether CPU system such as QJ71E71-100. Since the MC protocol is used as the communication protocol, it is also possible to communicate with KEYENCE PLC KV-5000, KV-7000 that can use the MC protocol.

◆Screen explanation

・IP address input

-Port number (decimal input)

・Connect to PLC with CONNECT button.

-Set the start address of the device to be monitored in Dwvice No.

-Only for Send Deta D device, you can write the input value with the DATA SEND button.

・~to Serial Set the number of addresses to write.

-Select Device Select the device to be monitored. Select either D, X or Y.

・Input button for X device

The upper two are momentary switches, and the lower two are alternate switches.

Please use it as a simple switch.　You can change the address by changing the value.

*Because the minimum unit of the X button switch is 1 word for protocol reasons, please note that all the upper 15 bits from the set address will be OFF.

Do not use near addresses with important contacts.

(Example: If set to X20, X21 to X2F will be turned off after the switch is operated.)

*2020/7/32 It has been improved that all the above 15 bits are OFF. It can be turned on in complete bit units.

*2020/7/32 Functional improvements. -It is now possible to save the IP address, port number, and simple switch address settings.

*For PLC Wi-Fi connection, see https://syoshinsya.mydns.jp/syosinsya/MelsecWifi.html

Please refer to it because it is introduced.

*When connecting the app to the PLC, it is necessary to set the PC parameters of the CPU in advance. Refer to https://syoshinsya.mydns.jp/syosinsya/MCprotocol.html for detailed settings of PC parameters.

* For smartphones, set the IP settings of the Wi-Fi network to connect from DHCP to

It needs to be changed to static and set according to the network IP address of the PLC.

* Due to the nature of wireless connection, if an unexpected connection failure occurs, it will not work fail-safe.

Never directly write to the device or operate switches that are related to (or correspond to) the power circuit or safety circuit.

In addition, we will not be liable for any problems or accidents that may occur while using this application.

Please use it.